Ignition coils

rammy1500

Supporting Member X2
Joined
Sep 27, 2006
Messages
1,006
Reaction score
41
Location
Columbus, Ohio
First off, I only ride the 900 a few times a year. I enjoy taking it out of the garage, pull the choke, turn the key and hit the start button and it fires up. Normally takes a few tries and fires up slow until all 4 cylinders kick in, then I'm off. But recently, it seems it is only running on 3 cylinders until a few trips around the block then all 4 kick in. Well yesterday, same routine, but never fired on all 4. Of course, first though is carbs need cleaned, ugh. So being a nice day, I figured I would dive a little deeper. So checking the spark is easier than removing and cleaning the carbs. Spark on 2 and 3 was non-existent. I repacked the coil with the original and still not firing on all cylinders. Pulled the air filter and shot some cleaner into the airbox, still not running correctly. Was about to push it back into the garage until I had a chance to pull the carbs, but figured to go ahead and swap the ignition coil on 1 and 4 cylinder. Guess what I found? I didn't even notice the crack on the first one I pulled, but did on the second. I paid good money from DB electrical for these coils.
So I know that Dyna sells good coils but does take modifications to get them to fit. I can steal a set off of one of the parts bikes, but those are already 40 years old. So any advice on other brands that you have had luck using?
 

Attachments

  • zl900 coils.jpg
    zl900 coils.jpg
    290.9 KB · Views: 2
Have you considered the stick coil mod?
 
Yes, I read through the thread, but since I only ride it a couple times a year, easier just to replace the coils and be done with it. Just looking for a new source since DB Electrical doesn't carry them anymore.
 
First off, I only ride the 900 a few times a year. I enjoy taking it out of the garage, pull the choke, turn the key and hit the start button and it fires up. Normally takes a few tries and fires up slow until all 4 cylinders kick in, then I'm off. But recently, it seems it is only running on 3 cylinders until a few trips around the block then all 4 kick in. Well yesterday, same routine, but never fired on all 4. Of course, first though is carbs need cleaned, ugh. So being a nice day, I figured I would dive a little deeper. So checking the spark is easier than removing and cleaning the carbs. Spark on 2 and 3 was non-existent. I repacked the coil with the original and still not firing on all cylinders. Pulled the air filter and shot some cleaner into the airbox, still not running correctly. Was about to push it back into the garage until I had a chance to pull the carbs, but figured to go ahead and swap the ignition coil on 1 and 4 cylinder. Guess what I found? I didn't even notice the crack on the first one I pulled, but did on the second. I paid good money from DB electrical for these coils.
So I know that Dyna sells good coils but does take modifications to get them to fit. I can steal a set off of one of the parts bikes, but those are already 40 years old. So any advice on other brands that you have had luck using?
Yes, I read through the thread, but since I only ride it a couple times a year, easier just to replace the coils and be done with it. Just looking for a new source since DB Electrical doesn't carry them anymore.
Hi mate. I replaced my old coils with Dynatek on my ZL1000. Floorless performance. Brackets weren't too difficult to fabricate. Bit of sheet ally or galvanised. See pictures:-
Yes, I read through the thread, but since I only ride it a couple times a year, easier just to replace the coils and be done with it. Just looking for a new source since DB Electrical doesn't carry them anymore.
 

Attachments

  • IMG-20261011-WA0010.jpg
    IMG-20261011-WA0010.jpg
    147.5 KB · Views: 5
  • IMG-20261011-WA0008.jpg
    IMG-20261011-WA0008.jpg
    156.1 KB · Views: 3
  • IMG-20261011-WA0009.jpg
    IMG-20261011-WA0009.jpg
    161.8 KB · Views: 3
  • IMG-20261011-WA0007.jpg
    IMG-20261011-WA0007.jpg
    151.7 KB · Views: 3
  • IMG-20261011-WA0004.jpg
    IMG-20261011-WA0004.jpg
    181.6 KB · Views: 4
  • IMG-20261011-WA0005.jpg
    IMG-20261011-WA0005.jpg
    128.4 KB · Views: 6
  • IMG-20261011-WA0013.jpg
    IMG-20261011-WA0013.jpg
    157 KB · Views: 6
  • IMG-20261011-WA0031.jpg
    IMG-20261011-WA0031.jpg
    148.1 KB · Views: 6
Ended up getting OEM style replacements from Square Motorcycle parts out of England. Took awhile to get to Ohio, but after replacing the spark plug wires and installing the new coils the bike fired right up just like the old days. Just in time to put it back into the garage for winter. I did notice and also have marked in my service manual that on my bike the red wire went to the negative side of the coil and the green/black wires went to the positive. I've heard it doesn't matter on the original coils but with aftermarkets it should be green/black to negative and red wires to positive. I might give them a switch and see if the new coils last longer than 7 years.
 
Back
Top