Bringing a 79' XS11 Special back to life

IMG_20191214_130641.jpg
$23.27 pads all around. Check the funky taper specific to the front end of the Special.

Time to clean up the chipped paint on the calipers and hose them down with some paint. It will be nice getting the parts off the bench and back on the bike.
 
A battery showed up. Ajc brand AGM $61.36 to the door. It's a big one compare to the ZL. It's been a while since the bike had power. First turn of key yields nothing. Check power to main fuse, good... ignition fuse good... couple more turns of key gets me some lights. The switches feel stiff but I didn't see corrosion when I had the controls off.

Starter turns motor over, tail light and brake light work, horn works. Turn signals light but no blinkey, no headlight high or low. From what I've read the fuse blocks are weak with the glass fuses and they take well to an upgraded block. I'll get it running before any upgrades, don't seem like too much trouble ahead to get the beast running.

Ol girl has been asleep for a long time.
 
IMG_20191216_152101.jpg
New air filter showed up. Should work better than the dried foam that was in there. Cheap too. The PO hacked the airbox, probably will patch that up. That must have been done when the Mac 4/1 no baffle megaphone was put on. SMHo_O
 
:hello: I repaired big holes in an air box using epoxo 88 flex. I taped a thin section of card board on the inside of each hole. Then mixed and applied the epoxy on the outside. The next day I formed the dried epoxo with my 3 inch air grinder. Then I sprayed it with plasti-dip from a rattle can. It came out so good that you couldn't tell where the repairs was.
 
Have your goodies arrived for your Xmas project? I had some issues with the turn signal switch a few months ago on my 79F. A friend from the XS11 site told me about some bad experiences he had cleaning his switches. Hooked me up with CAIG Deoxit an effective and safe cleaner for electrical contacts and connectors. Works very well on old switches and contacts. Also acts as a lubricant. The first two contact cleaners he tried actually dissolved some of the smaller internal plastic parts. I also gave up trying to figure out the headlight issue and hot wired it. The RLS ( Reserve Lighting Unit ) is a Demon in a plastic box surrounded by 40 year old wires and connections. YMMV
 
IMG_20191221_104934.jpg
10' of 1/4" fuel line to re-do the octopus, a buffer cleaner cause I ruined a couple of wheels in my days by using a screwdriver to clean them, and some 2" wool buffing pads.
IMG_20191221_105230.jpg
Nice looking vac gauge set, I'm a ways away from using it on the XS. May sync the gauges and use it on the ZL. I'll put the review in the tools thread. It was $64+tax on Amazon and if you look close there is a 10% off code on products from their site.

Thanks for the tip on the contact cleaner. I will see if the parts bike RLS box works.
 
IMG_20191221_160135.jpg
I guess these carb boots will fall into the good enough category. At $19.07 shipped I guess the nipples would face the wrong directions and pull out of the holes with a slight tug. Check everything over real close when using the aftermarket! I'll use some seal all and glue the thing in.

Also read that the headlight relay keeps it from turning on till the engine is running, not like the ZL that picks up the signal from the starter.
 
Thats it. I laid a towel across the tank just in case. It worked very well for me.
 
That stuff can actually lower the resistance between contacts but over time, it dries out and resistance and protection gets worse than just cleaning.
 
Brakes are off the bench and on the bike. Good pedal and lever feel. Not ZL good with the braided lines but tons better than when the bike showed up with crust in the reservoirs and the rear caliper hanging. The Mityvac works great for bleeding. Pump to 20", press or squeeze MC, open bleeder and close at 10".... repeat as needed.
1577656412466921638643106829589.jpg went with Allen head cap screws on the caliper bolts because the stock m8 x 95 were bent. The higher strength Allen bolts should hold up fine.
 
I've never had the luxury of a tool to assist with bleeding. Looks like it would be very helpful. Are the rear brakes back on as well? All of my XS 11's have very good brakes. Not all of them have braided lines though. Definately a better product. Whats next after the brakes?
 
Back
Top