cylinder 3 cold

kvalheim

Senior Member
Joined
Mar 31, 2013
Messages
415
Reaction score
43
Location
sparta
Got a question. bike has been running like a putter but. ran fine until stored it little over year ago. Went to get it out and it hardly ran. Had tank cleaned,petcock rebuilt, carbs done by Rick, new wires and cleaned tested fine. new spark plugs. fresh gas. Now when I ride it sounds like it just ain't running correct. thought maybe carbs needed further adjusting but noticed the exhaust pipe for cylinder 3 is cold. :wtf:
pulled plug wire off of cylinder 3 and put a old spark plug in it you can see it has spark.
Any ideas what to do lets here it :director:I am about ready to loose my cool:banghead:
pick up coil?
coil not working properly?
CDI box?
about ready to borrow a scope to look down cyliner to check piston?
 
1 and 3 fire simultaneously through the same coil. It shouldn't be electrical unless it is directly related to that plug, i.e.- plug,boot,wire. Did you put a fuel filter inline between the tank and carbs?
 
:hello: Undo # 3 spark plug cap & check it for 5 K ohms. Them old ass spark plug caps/boots can intermit even after a good cleaning. I know because I just spent 3 days fighting with my friends ZL 1000. I gave up on them & bought 4 straight new NGK resister spark plug caps. Take the 4 dust well caps covers from the stock caps & put them on the NGKs. Now I'm stuck pulling carbs, oil pan & flushing the coolant system.:pain10: :pain10: Then I'll be able to trouble shoot the fan circuitry. :pain10:IMG_4058.JPG IMG_4060.JPG IMG_4062.JPG You get these people who are to lazy to do stuff for themselves it just sickens me. Now I'm going to be set back even further on my own stuff. :pain10:
 
:hello: Are you sure that each coils spark plug wires are going to the correct spark plug. Also that the positive red & negative green wires are connected properly. Each coil has a - symbol & a + symbol marked on them as to were the electrical wires plug in.
 
Yes sir they are correct double and triple checked to make sure.
And only cylinder 3 exhaust pipe is cool.
 
Have you changed #1 & #3 wire to check out if cyl. #1 is now cold? Like prfixer wrote 1&3 fire @ same time, one is the 'main spark', the other the 'support spark' without power - the main spark only works if the mixture is correct.
 
Last edited:
So I swapped wires #1 and #3 around like prfixer said and now both cylinder #1 and #3 exhaust pipes are cold.
 
NOBODY noticed it: coil, LH serves cyl. #1 & #4 (NOT #3!!!!) and coil, RH serves #2 & #3 - was that the mistake? Sometimes unable to see the wood for the trees...:dontknow:
 
Holy Crap! CRS is in full swing at my house, sorry!
 
For the Dynas you will need some small L-brackets. I bought brackets at walmart hardware section, can't remember size. 3/4" x 3/4" maybe. They were Stanley brand. You could easily fab some also.
 
NOBODY noticed it: coil, LH serves cyl. #1 & #4 (NOT #3!!!!) and coil, RH serves #2 & #3 - was that the mistake? Sometimes unable to see the wood for the trees...:dontknow:
Yep, sorry again! 2 and 3 are the ones that I should have said to swap. At this point, I think I would pull the plugs themselves and make sure they aren't fouled. Clean them, dry them and reinstall and try to fire it up with the plug wires attached normally. If 3 is still cold, then swap 2-3 and 3-2 and see if the trouble goes to cylinder 2.
 
Back
Top